Dickwandige Kunststoff-Formteile wirtschaftlich fertigen = Economical production of thickwalled plastics mouldingBRAÊUNLICH, K; JOHANNSON, B. F.Kunststoffe. 1991, Vol 81, Num 4, pp 321-323, issn 0023-5563, 3 p.Article

Optimal heating of thick walled elementsTALER, Jan; TALER, Dawid.Heat exchange and renewable energy sources. International symposium. 2002, pp 183-192, isbn 83-88764-76-4, 10 p.Conference Paper

Etat élastoplastique d'un tube à paroi épaisseZADOYAN, M. A.Izvestiâ Akademii nauk SSSR. Mehanika tverdogo tela. 1987, Num 6, pp 113-120, issn 0572-3299Article

Torsion libre des barres en composite à parois épaissesVASIL'EVA, A. V.Mehanika kompozitnyh materialov. 1988, Num 2, pp 315-319, issn 0135-7492Article

Entlastung und sekundäres Fliessen in rotierenden elastisch-plastischen Hohlzylindern = Unloading and secondary flow in rotating elastoplastic tubeMACK, W.Zeitschrift für angewandte Mathematik und Mechanik. 1992, Vol 72, Num 1, pp 65-68, issn 0044-2267Article

Etat de contrainte des coques cylindriques à parois épaisses de section droite non circulaireGRIGORENKO, YA. M; VLAJKOV, G. G; SHEVCHENKO, S. N et al.Prikladnaâ mehanika (Kiev). 1986, Vol 22, Num 4, pp 37-43, issn 0032-8243Article

The strain-controlled creep damage law and its application to the rupture analysis of thick-walled tubesGU, R. J; COZZARELLI, F. A.International journal of non-linear mechanics. 1988, Vol 23, Num 2, pp 147-165, issn 0020-7462Article

A dugdale-type estimation of the plastic zone for a penny-shaped crack in a thick transversely isotropic layer due to radial shearDANYLUK, H. T; SINGH, B. M; VRBIK, J et al.Engineering fracture mechanics. 1995, Vol 51, Num 5, pp 735-740, issn 0013-7944Article

Vibration of thick elastic and viscoelastic tubes. I: Harmonic responseMOORE, I. D.Journal of engineering mechanics. 1990, Vol 116, Num 4, pp 928-942, issn 0733-9399, 15 p.Article

Excitation of a thick-walled radially polarized pizeoceramic cylinder by nonsteady-state electrical signalsBABAEV, A. E; RYABUKHA, YU. N; SAVIN, V. G et al.International applied mechanics. 1994, Vol 30, Num 9, pp 665-671, issn 1063-7095Article

Method of solving three-dimensional nonlinear dynamic problems for compound bodies of rotationROMASHCHENKO, V. A.Strength of materials. 1993, Vol 25, Num 6, pp 442-450, issn 0039-2316Article

The effect of preload on end-systolic pressure-wall thickness relationsMILLER, W. P; FLYGENRING, B. P.Journal of applied cardiology. 1990, Vol 5, Num 6, pp 431-441, issn 0883-2935Article

Automated process of removing internal defects in thick wall components and welded jointsSHTRIKMAN, M. M.Welding international. 2004, Vol 18, Num 5, pp 391-396, issn 0950-7116, 6 p.Article

Appendix : An example of a thick wallRESSAYRE, N.Publications mathématiques (Bures-sur-Yvette). 1998, Vol 87, pp 53-56, issn 0073-8301Article

Thick general shells under general loadingDONNELL, L. H.Journal of applied mechanics. 1989, Vol 56, Num 2, pp 391-394, issn 0021-8936Conference Paper

Erfassung instationärer Wärme-Beanspruchung Dickwandiger Kraftwerks komponenten durch Wandtemperatur-messung = Apparition de contraintes thermiques non stationnaires lors des mesures de température dans les parois épaisses de composants de centrale électriqueTALER, J.Brennstoff-Wärme-Kraft. 1987, Vol 39, Num 1-2, pp 30-36, issn 0006-9612Article

Überwachung der instationären wärmebeanspruchung in dickwandigen bauteilen von kraftwerksblöcken = Surveillance des contraintes thermiques instationnaires dans les éléments de construction de forte épaisseur dans les centrales électriquesTALER, J.Brennstoff-Wärme-Kraft. 1987, Vol 39, Num 11, pp 484-489, issn 0006-9612Article

Discontinuous solutions in the theory of plasticityARTEMOV, M. A; IVLEV, D. D.International applied mechanics. 1996, Vol 32, Num 7, pp 550-553, issn 1063-7095Article

Determining local stress and limit load in a thick-walled tube with a hoop direction U-shaped notch under tensionZHANG, Q. Y; LIU, Y.International journal of pressure vessels and piping. 1992, Vol 51, Num 3, pp 361-372, issn 0308-0161Article

Vibration of thick elastic and viscoelastic tubes. II: Response to patch loadingMOORE, I. D.Journal of engineering mechanics. 1990, Vol 116, Num 4, pp 943-951, issn 0733-9399, 9 p.Article

Methodology for predicting spray quenching of thick-walled metal alloy tubesMASCARENHAS, Nikhin; MUDAWAR, Issam.International journal of heat and mass transfer. 2012, Vol 55, Num 11-12, pp 2953-2964, issn 0017-9310, 12 p.Article

Determination of the pressurising pressure for welded thick-wall cylindrical shellsEROFEEV, V. V; SHAKHAMATOV, M. V; KOVALENKO, V. V et al.Welding international. 2002, Vol 16, Num 10, pp 802-804, issn 0950-7116Article

Influence of autofrettage on the stress intensity factors for a thick-walled cylinder with radial cracks of unequal lengthARONE, R; PERL, M.International journal of fracture. 1989, Vol 39, Num 1-3, pp R29-R34, issn 0376-9429Article

Stress intensity factors for a radially multicracked partially autofrettaged pressurized thick-walled cylinderPERL, M; ARONE.Journal of pressure vessel technology. 1988, Vol 110, Num 2, pp 147-154, issn 0094-9930Article

Optimal design of a thick-walled pipeline cross-section against creep ruptureRYSZ, M.Acta mechanica. 1987, Vol 66, Num 1-4, pp 83-102, issn 0001-5970Article